Skip to content

4 · Enhance & Master ​

Finishes an existing recording - a take you rendered earlier, or any song file - without a music model and without a GPU: a gentle EQ, loudness and dynamics, and a release export with tags and cover.

▶ Video: Tutorial 4 · Enhance & Master - the whole path in ComfyUI, narrated, with chapters. All of them in the tutorial playlist.

text
Load Audio -> Audio HQ 1-3 -> EQ -> Loudness & Dynamics -> Preview
                                        -> Export Release (FLAC 24-bit + MP3 V0, tags copied, original kept)

Quick start ​

  1. Open 4 · Enhance & Master from the template browser.
  2. Upload the file in Load Audio (FLAC, WAV, MP3, OGG, M4A ...).
  3. Press Run. The defaults: Audio HQ 1 and 2 with the standard preset, a warm, gentle tone match, -14 LUFS with a true peak of at most -1 dBTP (streaming), Balanced - gentle glue compression, the source's sample rate.
  4. The result plays in the preview; the files are in output/plenio/enhanced/:
    • <title>.flac and <title>.mp3 - the master, with the source file's tags and cover,
    • <title> (original).flac - the unmastered source, for comparison,
    • <title>.plenio.json - the release record (settings, measured loudness, reports).

The stages ​

Audio HQ (guide) - three nodes before the EQ: HQ 1 · Stereo Cleanup calms the unsteady stereo shimmer of AI renders in the highs; with the HQ Mastering switch at the top on (on by default) HQ 2 · Regenerate Highs generates new highs above 8.2 kHz with the UniverSR model (229 MB; about 1.5 s per second of music on an RTX 5060 Ti) - fewer AI shimmer and artifacts, and the cure for a band-limited source such as an old MP3; HQ 3 · De-Reverb (bypassed) dries a short metallic room but also dulls the highs. There is no brief here, so their presets are standard; choose gentle (classical, jazz, folk), strong (rock, metal, punk) or wide (electronic, dance, ambient) to match your music.

EQ (help) - flat (no change), manual (drag bands on the curve under the node; double-click adds a band, the wheel changes Q), match preset (Plenio measures the audio and proposes up to a few gentle peak bands towards a warm or bright tilt, or towards a reference recording you connect), custom match (the same with your own strength and limits). The EQ does not normalise: a boost can raise the peak - the next stage takes care of level.

Loudness & Dynamics (help) - a target (streaming -14, Apple Music / podcasts -16, dynamic -18, broadcast EBU R128 -23, loud -9 LUFS, or custom), a compression style (or off for the limiter alone), and the output sample rate. The node measures the result and says whether the target was reached; when reaching it would need more limiting than the style allows, it stops short and warns instead of squashing the song.

Export Release (help) - FLAC 24-bit, MP3 VBR V0 and/or WAV 32-bit float; tags title only, typed tags, or copy from loaded file (the file in the one Load Audio node of the workflow; the title input, when connected, wins). A connected cover image replaces the copied cover.

Correcting the lyrics ​

Export writes a sung recording's lyrics - the subtitles, the lyrics tag and the release record - from what the lyrics ASR (Qwen3-ASR, or Whisper) hears, misheard words included. To correct them, select the two nodes of Lyrics (optional) under the source and press Ctrl+B:

  1. Run: Transcribe Lyrics hears the words and the Song Sheet · Lyrics stops the run (stop for review); nothing is exported yet.
  2. Open the Song Sheet's editor, fix the words (and the section tags, if you like) and Approve.
  3. Run again: Export times your words to the singing. They go into the subtitles (lines).srt, the release record and the lyrics tag - also over the lyrics tag copied from the loaded file. (sung).srt keeps what was heard, as the player's as sung view shows it.

You can also type the lyrics into the Song Sheet yourself: a manual document is never replaced, and nothing is transcribed then. The block is bypassed by default, so an instrumental recording runs through without a stop.

Using it after a song path ​

The song templates 1-3 and 5 finish with the same stages as the Plenio · Master block (node library, Plenio/Mastering): it sits between the render and Export Release, and Export keeps the unmastered take as (original).flac. Use this template to master a take again with other settings.

Skipping a stage ​

Bypass a node (Ctrl+B) or choose flat in the EQ: the audio then passes through unchanged - same samples, sample rate and length; Export still writes the tags you chose. Choose keep as the sample rate to never convert.

App mode ​

Switch Graph / App at the top left: the app asks for the file, HQ mastering, the presets of HQ 1 and HQ 2, the EQ mode, the loudness target and the compression style (App mode).

Good to know ​

  • The targets are measured, not estimated: integrated loudness per ITU-R BS.1770-4 and true peak with 4x oversampling, after the final sample-rate conversion. The export's record shows the numbers again, measured on the exported audio. Details and limits: Mastering and audio formats.
  • A song that is already loud and limited (most commercial masters) gains little from another pass; the original file lets you compare.
  • Cover art is embedded into FLAC and MP3 only when the optional package mutagen is installed (<ComfyUI python> -m pip install mutagen); without it the cover is saved as <title>.jpg next to the audio and the export notes this. WAV files carry basic tags (RIFF INFO) and no cover.